Not only do we have the largest range of stainless steel fasteners in the country, but we also stock a variety of chemicals and tools to look after it for years to come.
Care should always be taken when using tools with stainless steel to avoid cross contamination from non stainless fasteners and a separate tool or bit should be used only for stainless steel.
Instruction sheets are available. If you are unsure how to use the tool please ask one of our staff and they will be happy to explain it to you.
|
Grunt Emergel - Stainless Steel requires regular cleaning and maintenance. Poorly specified, designed, manufactured or maintained Stainless can suffer rust discolouration often known as Tea-staining. If tea-staining does occur, the Nickel Institute recommends application of a phosphoric acid gel to remove the staining and restore the surface of the stainless steel. Grunt Emergel is recommended for the use of removing:
|
|
Lubricants and Corrosion Inhibitors are chemicals or natural products that aid in the prevention of thread galling or cross threading and decay by oxidisation.
|
Prolan Lanolin Lubricants - Lanolin General Purpose Liquid, non-conductive to 70kV, used as a lubricant for drilling, cutting and machining, excellent rust proofing and great for lubricating locks, hinges and light chain. Lanolin Heavy Duty Liquid, ideal for use in harsh and highly corrosive environments, lubricates protects and extends the life of high speed and load bearing chains, lubricant for wire ropes, protects battery terminals, boxes and connectors, outside storage protection. Lanolin Grease, Food grade, non conductive to 70kV, potable water grease, salt spray tested to AS 2331.3.1, rubber grease, nozzle dip and anti-seize for threaded rods, stops galling of stainless and aluminium, stops electrolysis due to dissimilar metals, non perishing to rubber O rings and seals. |
|
 |
Tef-Gel is derived from a specially formulated Teflon paste and is used in highly corrosive environments in areas of Rust Prevention, Galvanic Corrosion Elimination as Anti Seize Lubricant. Tef-Gel is ideal to isolate and separate dissimilar materials such as Aluminium and Stainless Steel, where in the presence of salt water and in contact galvanic corrosion can occur. |
|
 |
CRC CDT Cutting compounds are superior neat cutting, drilling, tapping and reaming lubricants that are formulated for hand and machine cutting on all types of metal. They significantly reduce friction and wear, increase cutting speeds, protect and extend tool life and ensure consistent, high quality surface finishes. They leave an anti-corrosive residue that is safe to use on soft metals suck as brass, copper and aluminum. Features and Benefits:
Also ideal for tube drawing and extruding, cold forming and deep drawing of difficult steels such as stainless steel, high nickel alloys, chrome alloys, nimonics and aluminium. |
|
 |
Chemz Nickel Anti-seize is designed for Stainless Steel fasteners. It is formulated to prevent the seizure of threaded components which are subjected to extremely high temperatures or adverse environmental conditions. |
|
|
Loctite Non-Metallic Anti-Seize Provides outstanding lubrication for all metals including Stainless Steel, aluminium and soft metals up to 1315°C |
|
 |
Nickel Anti Seize is formulated to prevent seizure of threaded components which are subjected to extremely high temperatures or adverse environmental conditions. |
|
 |
Chemical Anchors - Fischer Chemical Anchors are a styrene-free polyester resin for fixings in masonry building materials. Resin and hardener are stored in two separate chambers and are not mixed and activated until pushed through the static mixer. Partially-used cartridges can easily be reused by changing the static mixer. FIS P 300 with longer curing time and lower application pressure can be extruded by using a conventional application gun. |
|
 |
Our chemical mortar accessories compliment our Fischer chemical anchors. The cleaning brushes are made with stainless steel bristles for cleaning drill holes in concrete and masonry. |
|
 |
Loctite Primers and Activators The Loctite Primer is a transparent, yellow to amber liquid activator used tfor increasing the cure speed of the loctite anaerobic products under low prevailing temperatures. The 7649 Activator is a solvent based activator for surface preparation that provides for low temperature curing. |
|
 |
Loctite Instant Bonding and Adhesives - universal, low viscosity, very fast fixture speed at 3 - 10 seconds, particularly suited for bonding a wide variety of materials, is colourless and suitable service temperature range is -40 °C to +120 °C. |
|
 |
Loctite Thread Sealant - Loctite 567 Thread Sealant withstands temperatures to 400 °F with excellent solvent resistance. Locks and seals tapered pipe threads and fittings, including high pressure applications. Disassembles with hand tools and is RoHS compliant. |
|
 |
Loctite Threadlockers - Loctite 243 and 277 thread locker compounds offer high performance on various metals even without use of an activator, temperature resistant to 180°C, superior heat ageing resistance, robust curing performance on fasteners with oil contamination traces and tolerant to industrial oils. |
|
Metric Jobber Drill Bits |
Drill bits or jobber drill bits are available in almost any size including metric and imperial diameters and if we don't have the size you need ex-stock please ask and we can source it for you. |
|
Imperial Jobber Drill Bits |
||
 |
These drill bits come with cutting edges on both ends, and can drill more holes before needing to be resharpened than standard single-ended drill bits. Titanium Nitride Coating inscreases hardness and decreases friction. Suitable for drilling plastic, wood and metal including Stainless Steel. |
|
 |
Black oxide coating maximises lubricant hold, therefore assisting chip flow and heat dissipation. 118° split point, ideal for drilling pilot holes. Ideal for the widest range of materials: Steel, wood plastic and stainless steel. |
|
 |
Available in a range of sizes and quantities in both metric and imperial |
|
 |
|
|
 Long Series Bits |
The Long Series drill bit starts at a length of 95mm. The Extra Long drill bit is an overall length of 315mm for all sizes. |
|
Extra Long Series Bits |
||
 Zentro 4 Masonry Drill Bit |
Masonry Drill Bits. |
|
 Masonry SDS Plus |
||
 |
The Turbo-bore spade bits have double outside spurs that provide a clean hole and reduce vibration. Unique twist design cuts faster than standard spade bits. |
|
 |
Precision ground for fast clean drilling in all types of wood. Threaded tip for self centering and self feeding. Flute geometry enables fast drilling. Hex Shand. Designed for heavy duty boring in wood and cuts through nail embedded wood. |
|
|
Tips or bits come in a range of drives to suit all screws. We also have tips for our range of security screws. |
|
 |
Can be used with our range of socket screws |
|
 |
Hand Taps are used to create a female thread on the inside of a pre-drilled hole, Anzor has a range of tap sets from M4 through to M12 but more are available on request. Taper Taps have a lead of eight threads and are used as a starting tap in difficult or high precision holes. They can be identified by a single ring on the shaft near the driving square. Intermediate Taps have a lead of four threads and are used in most general purpose applications. They can be identified by two rings on the shaft near the driving square. Bottoming Taps have a lead of two threads and are used when tapping blind holes. Usually preceded by a taper or intermediate tap. They can be identified by their plain shaft (no rings near the driving square). We also have a Gun Tap which is specifically for tapping the hole for our Anzor Eyelet. |
|
 |
Hex Nutsetters drive fasteners using the corners to drive. Torsion Nutsetters are designed to withstand extreme torque delivered by cordless drills and impact drivers. |
|
 |
Suitable for pneumatic impact tools and come in 1/2 inch drive. |
|
 |
Long lasting and suitable for all general purpose and stainless steel cutting. |
|
 |
High quality Stainless Steel grade grinding discs. Depressed centre, well balanced and long lasting. Suitable for all general purpose grinding. MPA tested in Hannover, Germany and manufactured to EN12413 standards. |
|
 |
A range of wire cutters for all of our Stainless wire rope |
|
 |
Our hand operated threaded insert tool is used for our aluminium and stainless threaded inserts |
|
 |
Our hand operated and air riveting tools can be used on our rivets |
|
 |
Demolition blades can be used on wood with nails, cement board, wood, PVC. Thick .062“ blade for long lasting demo cuts. TPI 6. Thin Metal blades are best for thin metal cuts less than 1/8“ such as copper pipe. Thin .035“ kerf blade for fast flexible cuts. TPI 24. Thick Metal blades are best for thick metal cuts 1/4“ to 1/2“ such as metal and cement board. Thin .035“ kerf blade for fast flexible cuts. TPI 14. Medium metal blades are best for medium metal cuts 1/8“ to 1/4“ such as metal, copper pipe and cement board. Thin .035“ kerf blade for fast flexible cuts. TPI 18. |
|
 |
We have a range of knives and tools along with refil blades to suit your needs. |
|
 |
We also stock Gun Nail Tools to go along with our Gun Nails. If we don't have what you require, contact your local branch. |
|
 |
Our bi-metal holesaws come with 8% cobalt welded teeth for extended life in industrial applications. 4/6 variable tooth configuration reduces vibration for a smooth, accurate cut. Ideal for Steel, stainless steel, cast iron, non-ferrous metal, wood and plastic. Cutting Fluid is recommended for increased life when drilling steel. |
|
 |
Our hex swage and crimping tools are suitable for our wire crimps and Marine swage fittings. |
|
 |
Masonry - Diamond braised edged blades designed for mortar removal, brick & block, concrete and nails. Metal and Fasteners - Plunge or flush cut into soft metals and sheet metal. Wood - General Purpose Bi-Metal blade for flush or plunge cutting solutions. Also great for cutting fibreglass, PVC, copper pipes and soft metal mesh. NB, cutting any type of metal will reduce the life of the blade. |
|
Anzor's 2024 Christmas Opening Hours
Build Your Deck Faster With Our Decking Screw Calculator
Do it once, do it right with Fischer FBS II Concrete Screw Bolts.
To receive useful info and product updates add your details below
Request a copy of our Engineering & Marine, or Construction Wall Chart.
Click here to download a PDF of our Engineering Catalogue. This catalogue includes stainless fasteners and fittings, marine hardware and construction brackets.
Click here dot download a PDF of our Construction Catalogue. This catalogue includes stainless/galvanized fasteners and fittings, and construction brackets.
